loading

A professional manufacturer of measuring & testing equipment.

About elongation after metal breaking

About elongation after metal breaking

About the elongation of metal after breaking, your company cannot automatically measure the elongation after breaking of our testing machine. Our company explains as follows: 1: The measuring method of elongation after breaking is to do the following work 1-1: First of all To know the sample ∫ use the sixth sheet of the standard to see how the gauge length is calculated: 6 sample 6 1 shape and size 6. 1.1 general requirements The shape and size of the sample depends on the metal product to be tested Shape and size. Generally, samples are cut from products, pressed billets or ingots and machined to make test specimens. However, products with constant cross-sections (profiles, bars, wires, etc.) and cast samples (cast iron and cast non-ferrous alloys) can be tested without machining. The cross-section of the sample can be round, rectangular, polygonal, or annular , It can be some other shapes under special circumstances. The sample whose original gauge length is related to the original cross-sectional area is called the proportional sample. The value of the ratio coefficient k used internationally is 5.65. The original gauge length should not be less than 15 mm. When the cross-sectional area of u200bu200bthe sample is too small, so that the value of the scale factor k of 5.65 cannot meet this minimum gauge length requirement, a higher value can be used (the value of 11.3 is preferred) or a non-standard value can be used. Proportional sample. The original gauge length (L o) of non-proportional specimens has nothing to do with its original cross-sectional area (S. ). Example: If my sample is 4mm in width and 4mm in thickness, then my gauge length is substituted into the formula u003d5.65×√4*4 u003d5.65*4 u003d22.6, that is, the gauge length of the sample is 22.6mm. Know the gauge length, how should we do the experiment: We quote the standard, so our correct test method is: draw a line at the beginning of the sample:, draw a mark every 22.6 mm until the end, and then on the testing machine Do a test to see where the breaking point of the sample is, and then connect it. Measure its deformation, and then substitute the formula to calculate the elongation after breaking. For the user, install a sensor on the sample (if the elongation can be measured, To meet the following condition 1: The gauge length of the extensometer is equal to the gauge length of the sample (this is impossible because the gauge length of the extensometer is an integer, such as 5 mm. 10 mm. 20 mm. 25 mm... The gauge length of the sample is determined by its own cross-section, so the gauge length of the sample cannot be equal to the gauge length of the extensometer, so it is not possible to use the gauge length of the extensometer as the gauge length of the sample)

GET IN TOUCH WITH Us
recommended articles
200 FAQs WHAT' S NEW APPLICATION
How to keep the hydraulic universal testing machine clean



Hydraulic universal testing machines have very high accuracy requirements.
Connection of hydraulic system of tensile testing machine



The hydraulic system is the power drive mechanism of the tensile testing machine.
Application of electronic universal testing machine in automobile industry



The specific application of the electronic universal testing machine in the automobile manufacturing process: The electronic universal testing machine needs to be used for automobile parts.
Wave soldering workflow



Wave soldering refers to the molten solder (lead-tin alloy), sprayed by electric pump or electromagnetic pump into the solder wave required by the design, can also be formed by injecting nitrogen into the solder pool, so that it is pre-loaded The printed board of the component realizes the soft soldering of the mechanical and electrical connection between the solder end or the pin of the component and the pad of the printed board through the solder wave.
Protection of frequency converter of hydraulic universal testing machine



The frequency converter is a power control equipment that uses frequency conversion technology and microelectronics technology to control AC motors by changing the frequency of the motor's working power supply.
Common failures of electronic universal testing machine



Electronic universal testing machine is a necessary equipment to control the quality of products.
Calibration method of electronic universal testing machine



The calibration operation of the electronic universal testing machine is still relatively unfamiliar to friends who use it for the first time.
Brief introduction of selective wave soldering defects and prevention



Selective wave soldering defects and their prevention.
Some precautions when using the testing machine



Testing machine, broadly speaking, is an instrument that verifies the quality or performance of a product or material according to the design requirements before it is put into use.
How to measure the tensile force of the testing machine



The tensile force is not an accurate value after being measured by the testing machine, and subsequent calculations are required to get the desired value.
no data

  Tel: 0086-0769-2318 4144

  Mobile: 0086-137 2828 8444

no data
CONTACT US

Copyright © 2025 Sinowon | All Rights Reserved.

Customer service
detect