loading

A professional manufacturer of measuring & testing equipment.

What are the test methods of the steel bar bending test machine

What are the test methods of the steel bar bending test machine

Regarding the test method of the steel bar bending test machine, the following test machine will give a brief introduction to the test method of the steel bar bending test machine. I hope it can help you! Selection of the test: 1. General requirements: A. Straightening: For the sample made from the coil, simple bending and straightening should be carried out before any test, and the smallest plastic deformation should be ensured. B. Artificial aging: when determining the performance indexes of tensile test and fatigue test, artificial aging of the sample can be carried out as needed (for the sample that needs to be straightened, artificial aging should be carried out after straightening). When the product standard does not specify the artificial aging process, the following process conditions can be used: heating the sample to 100°C, holding it at 100°C ± 10°C for 60 min to 75 min, and then naturally cooling to room temperature in still air. When artificially aging the sample, the aging process conditions should be recorded in the test report. 2. The parallel length of the sample should be long enough to meet the requirements for elongation determination. 3. When measuring the elongation (A) after breaking, the sample should be marked with the original gauge length L according to GB/T 228.1. 4. When measuring the total elongation of force Fm (Ag,) by manual method, the equal division mark should be marked on the parallel length of the sample. According to the diameter of the steel product, the distance between the equal division marks should be 10 mm. 5 mm or 20 mm can also be used as required. Selection of test equipment: 1. Chenda GW40/50 steel bending test machine, which is calibrated and calibrated according to the national standard. 2. The bending test can also be done by using a test device with two supporting rollers and a bending core. . 3. The extension gauge used to measure the force and total elongation should have a gauge length of at least 100mm, which should be recorded in the test procedure: 1. Unless otherwise specified, the bending test should be at a temperature of 10℃~35℃ Proceed under. Note: For the test at low temperature, if the test conditions are not specified in the agreement, a temperature deviation of ±2°C should be used. The sample should be immersed in the cooling medium and kept for sufficient time to ensure that the entire sample reaches the specified temperature (for example, at least 10 min for liquid medium and at least 30 min for gas medium). The bending test should be carried out when the sample is removed from the medium 55. Moving the sample should ensure that the temperature of the sample is within the allowable temperature range. 2. The sample should be bent on the bent core. 3. The bending angle (T) and bending core diameter (D) should comply with relevant product standards. Judgment of test results: The bending test shall be determined according to the relevant product standards. When the product standard does not stipulate, if there is no visible crack in the bent sample, the sample is judged to be qualified.

Previous: The main purpose of the pressure testing machine

Next: The main structure and working principle of the testing machine

GET IN TOUCH WITH Us
recommended articles
200 FAQs WHAT' S NEW APPLICATION
How to keep the hydraulic universal testing machine clean



Hydraulic universal testing machines have very high accuracy requirements.
Connection of hydraulic system of tensile testing machine



The hydraulic system is the power drive mechanism of the tensile testing machine.
Application of electronic universal testing machine in automobile industry



The specific application of the electronic universal testing machine in the automobile manufacturing process: The electronic universal testing machine needs to be used for automobile parts.
Wave soldering workflow



Wave soldering refers to the molten solder (lead-tin alloy), sprayed by electric pump or electromagnetic pump into the solder wave required by the design, can also be formed by injecting nitrogen into the solder pool, so that it is pre-loaded The printed board of the component realizes the soft soldering of the mechanical and electrical connection between the solder end or the pin of the component and the pad of the printed board through the solder wave.
Protection of frequency converter of hydraulic universal testing machine



The frequency converter is a power control equipment that uses frequency conversion technology and microelectronics technology to control AC motors by changing the frequency of the motor's working power supply.
Common failures of electronic universal testing machine



Electronic universal testing machine is a necessary equipment to control the quality of products.
Calibration method of electronic universal testing machine



The calibration operation of the electronic universal testing machine is still relatively unfamiliar to friends who use it for the first time.
Brief introduction of selective wave soldering defects and prevention



Selective wave soldering defects and their prevention.
Some precautions when using the testing machine



Testing machine, broadly speaking, is an instrument that verifies the quality or performance of a product or material according to the design requirements before it is put into use.
How to measure the tensile force of the testing machine



The tensile force is not an accurate value after being measured by the testing machine, and subsequent calculations are required to get the desired value.
no data

  Tel: 0086-0769-2318 4144

  Mobile: 0086-137 2828 8444

no data
CONTACT US

Copyright © 2025 Sinowon | All Rights Reserved.

Customer service
detect